GB/T 7730.1-2002 锰铁及高炉锰铁 锰含量的测定 电位滴定法和硝酸铵氧化滴定法
作者:标准资料网 时间:2024-05-21 05:33:01 浏览:8172
来源:标准资料网
基本信息
标准名称: | 锰铁及高炉锰铁 锰含量的测定 电位滴定法和硝酸铵氧化滴定法 |
英文名称: | Ferromanganese and blast furnace ferromanganese--Determination of manganese content--Potentiometric method and titrimetric method after ammonium nitrate oxidation |
中标分类: |
冶金 >>
金属化学分析方法 >>
钢铁与铁合金分析方法 |
ICS分类: |
冶金 >>
铁合金
|
替代情况: | 替代GB/T 7730.1-1987;被GB/T 5686.1-2008代替 |
发布部门: | 中华人民共和国国家质量监督检验检疫总局 |
发布日期: | 2002-09-11 |
实施日期: | 2003-04-01 |
首发日期: | 1987-05-12 |
作废日期: | 2008-11-01 |
主管部门: | 中国钢铁工业协会 |
提出单位: | 原国家冶金工业局 |
归口单位: | 全国钢标准化技术委员会 |
起草单位: | 新余钢铁有限责任公司 |
起草人: | 段清国、周学政、范青 |
出版社: | 中国标准出版社 |
出版日期: | 2003-04-01 |
页数: | 平装16开, 页数:7, 字数:13千字 |
书号: | 155066.1-19002 |
适用范围
本部分规定了用电位滴定法和硝酸铵氧化滴定法测定锰含量的原理、试剂和材料、仪器、取制样、分析步骤、结果计算等。本部分适用于锰铁及高锰铁中能含量的测定,测定范围(质量分数):50.00%~95.00%。方法一不适于铬含量(质量分数)>0.4%的锰铁及高炉锰铁中含量的测定。
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类: 冶金 金属化学分析方法 钢铁与铁合金分析方法 冶金 铁合金
Product Code:SAE AMS2263
Title:Tolerances, Nickel, Nickel Alloy, and Cobalt Alloy Tubing
Issuing Committee:Ams F Corrosion Heat Resistant Alloys Committee
Scope: This specification covers established inch-pound manufacturing tolerances applicable to seamless and welded thin-wall aircraft tubing of nickel, nickel alloys, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions and are based on individual measurements, unless otherwise noted. The term "exclusive" is used to apply only to the higher figure of a specified range.【英文标准名称】:Solidwoodpanels(SWP)-Requirements.
【原文标准名称】:实木板材(SWP).要求
【标准号】:NFB54-178-2009
【标准状态】:作废
【国别】:法国
【发布日期】:2009-02-01
【实施或试行日期】:2009-02-14
【发布单位】:法国标准化协会(FR-AFNOR)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:外观;抗弯强度;板材结构;板材;体密度;分类;分类系统;定义;尺寸公差;干燥面积;外部面积;精整;甲醛;甲醛释出;湿度范围;作标记;机械性能;弹性模量;生产控制;性能;实木;规范(验收);符号;木材;木基质产品;木质板材;木材加工
【英文主题词】:Appearance;Bendingstrength;Boardconstruction;Boards;Bulkdensity;Classification;Classificationsystems;Definition;Definitions;Dimensionaltolerances;Dryareas;Exteriorareas;Finishes;Formaldehyde;Formaldehydeemissions;Humidityranges;Marking;Mechanicalproperties;Modulusofelasticity;Productioncontrol;Properties;Solidtimbers;Specification(approval);Symbols;Wood;Woodbasedproducts;Woodbasedsheetmaterials;Woodworking
【摘要】:
【中国标准分类号】:Q71
【国际标准分类号】:79_060_99
【页数】:18P;A4
【正文语种】:其他